Skyline Audio
Contour rev 0.3 · boards and parts in hand, not yet measured

Eight switches,no pots.

A 1U stereo Baxandall equaliser for mastering and bus work. Two shelves, a high-pass and a low-pass, and every control is a stepped switch, so any setting can be written down and recalled exactly.

Front panel · click the right or left side of a knob to turn it
Drawn from ideal shelf and filter maths at the labelled frequencies. It shows what the controls do. It is not a measurement.
Format1U stereo19-inch rack, balanced XLR in and out
Range±4.5 dB11 steps a band, 0.5 dB near zero
Frequencies6 + 6Bass 23 to 220 Hz, treble 1.9 to 19 kHz
Dynamic range122 dBSimulated, not yet measured
Controls

Finer steps where the moves are small.

Bus and mastering moves usually live within a decibel of flat, so that's where the steps are closest: 0.5 dB around zero, then 1 dB, then 1.5 dB out to ±4.5. Gain is set per channel. Frequencies and filters are ganged for stereo.

  • HIGH PASSOut, 20, 30, 41, 50, 71 Hz

    12 dB/oct, both channels together.

  • BASS FREQ23, 42, 57, 92, 155, 220 Hz

    The bass shelf's half-gain point, both channels together.

  • BASS L, R−4.5 to +4.5 dB, 11 steps

    Bass shelf gain, one switch for each channel.

  • TREBLE L, R−4.5 to +4.5 dB, 11 steps

    Treble shelf gain, one switch for each channel.

  • TREBLE FREQ1.9, 3.9, 5.9, 8.6, 13, 19 kHz

    The treble shelf's half-gain point, both channels together.

  • LOW PASSOut, 12, 17, 21, 24, 36 kHz

    6 dB/oct, both channels together.

  • EQ INToggle, red LED

    Hard-wire bypass by relay. The LED lights when the EQ is in.

Signal path

Four stages, all through-hole.

Every part is in current production and soldered by hand, with the op amps in machined sockets. The receiver and the EQ stage each invert, so the two cancel: hot in is hot out, and gain at flat is unity.

Stage 1 · input

Differential receiver

A discrete balanced receiver built on 0.1 % resistors, behind ferrite beads on each leg.

NE5534A
0.1 % resistors
Stage 2 · filters

High-pass and low-pass

Relays switch the filter parts. A JFET op amp keeps DC offset out of the high-pass.

OPA2134
Film and C0G capacitors
Stage 3 · EQ

Baxandall shelves

Switched 1 % resistor ladders set the gain. Shelf capacitors are hand-paired left to right within 0.5 %.

NE5534A
Kemet film, TDK C0G
Stage 4 · output

Balanced line driver

Drives the output XLR through the bypass relay. Simulated maximum output is +27 dBu.

DRV134
Omron G5V-2 relay
Switching

A click should change one thing.

Rotary switches break one contact before they make the next. Left alone, that gap is audible. Most of the design work in Contour went into what happens between positions.

The filter knobs carry no audio

They only steer relays that sit next to the circuit, so the signal path stays short. Between positions no relay is on, which is the same as OUT, so nothing jumps.

A keeper holds the bass flat

A resistor holds the bass network at its 0 dB tap while the switch is between contacts. In simulation the response stays within 0.05 dB of flat during a click. Without it, the sub-bass would dip by about 10 dB.

Bypass is a wire

With EQ IN off, or with the power off, a relay connects each input straight to its output. Switching the EQ in makes a click of about −54 dBu in simulation.

Specifications

Simulated so far. Bench numbers to come.

The first unit is going together now and nothing has been measured. The figures below come from simulation of the whole circuit with part tolerances. Bench measurements replace them as they come in.

ParameterConditionSimulatedBench
Flatness20 Hz to 20 kHz, gains at 0, all 36 frequency settings±0.03 dBPending
Gain step accuracyAll 11 positions, bass and trebleWithin 0.022 dBPending
Shelf frequencyAgainst the panel labelWithin 1.4 %Pending
Left/right matchEQ stage, parts at tolerance, 95th percentile0.037 dBPending
Output noise22 Hz to 22 kHz−95.3 dBuPending
Dynamic rangeMaximum output over noise122 dBPending
Maximum outputEQ flat+27.0 dBuPending
Maximum inputBoth shelves at +4.5 dB, ±15 V supply+22.5 dBuPending
Left/right crosstalk1 kHz / 20 kHz, rev 0.3 layout−68 / −47 dBPending
Common-mode rejection0.1 % resistors, 5th percentile54 dBPending
High-pass corners−3 dB points20.2 / 30.0 / 41.2 / 49.6 / 71.6 HzPending
Low-pass corners−3 dB points11.7 / 16.6 / 21.5 / 24.1 / 36.2 kHzPending
PowerExternal supply, 5-pin XLR±15 to 18 V DC
Front panel19-inch rack, 1U482.6 × 43.7 mm
Contour rear panel legend, seen from the back: right channel in and out, power inlet, left channel out and in

Rear panel artwork, seen from the back. Connector holes are shown as outlines.

Connections

Five XLRs and no mains.

  • AudioBalanced XLR in and out for each channel, on Neutrik connectors.
  • Power±15 to 18 V DC from an external supply on a 5-pin XLR. There is no mains voltage inside the case.
  • Case1U, about 200 mm deep. Black anodised front panel with a white legend.
  • BoardsTwo. The switches and EQ sit on a board directly behind the panel. The rest lies flat behind it.
First units

Boards are in. The case is next.

Contour's boards and parts are in hand and the first unit is going together. Leave your email and we'll send bench measurements, photos and the price when it's ready.