Skyline Audio
SA-425 Rev A · prototypes in build

The 425,in 2520.

A discrete op amp built around the circuit of a late-1960s Los Angeles console amplifier, redrawn for the 2520 footprint. Even-order colour, two solder-jumper flavours, and it runs on ±12 to ±24 V.

Top side · drawn from the Rev A board file
Footprint252028.6 × 28.6 mm, five pins
Supply±12–24 VSame behaviour across the range
Flavours2 × 2HF and CLIP, set with an iron
Character2nd orderMostly second harmonic, like the original
The original

Pink epoxy. Octal socket. Nowhere to plug it in.

The 425 never fit the 2520 world. So we moved the circuit, not the myth.

The Opamp Labs 425 was a plug-in amplifier made in Los Angeles in the late 1960s and early '70s. It came potted in pink epoxy on an octal socket and ran inside Opamp Labs consoles and channel strips. DIY builders used it as a mic pre, a line driver, a summing amp and as EQ make-up gain.

People describe its sound as colour that gets interesting when you push it. The distortion is almost pure second harmonic, and it has a famous quirk: after it clips, the output sticks at the rail for a moment before it lets go.

Original 425s are scarce and their parts are gone. As far as we can find, nobody has put the circuit on a 2520 board. The SA-425 does, with the same three stages, modern parts, and the original's behaviour one solder jumper away.

Watch the documentary about the last Opamp Labs console
Original 425
Package
Potted module, pink epoxy
Mount
Octal socket
Topology
Matched NPN pair, 4009 hybrid, complementary output
After clipping
Sticks at the rail
SA-425
Package
Two-sided 1.6 mm board
Mount
2520 pin pattern
Topology
The same three stages
After clipping
Your choice: stick, or recover fast
Signal path

Three stages, the way the 425 did it.

No IC anywhere. The parts change, the topology doesn't. What we added sits around it: current-sink bias, current limiting, rail filtering and input clamps.

Stage 1 · input

Matched NPN pair

A dual transistor on one die, so both halves track in temperature. Fed by a current sink, so the bias holds from ±12 to ±24 V.

BCM846BS matched pair
BC846B tail sink
Stage 2 · gain

4009-style hybrid

A second NPN pair drives a PNP common-emitter gain stage, the heart of the 425's sound. Its current is limited, so a fault can't cook it.

BCM846BS pair → MMBT5401
MMBT5401 limiter
Stage 3 · output

Complementary pair

A pair of SOT-223 power transistors with diode bias. They drive 600 Ω lines and survive a brief short to ground.

BCP56-16 / BCP53-16
BAS116 bias diodes
Flavours

Modern manners or vintage misbehaviour.

Three solder jumpers on the top side choose how the module behaves. They ship in the defaults below, and you can change them with an iron after the module is built.

HF

JP1 + JP2

CLIP

JP3

Specifications

Targets, and where we are.

The figures below come from simulation with the transistor makers' own models. Bench measurements from the Rev A prototypes replace them as they come in. We won't print a number we haven't measured as if we had.

ParameterConditionTargetSimulatedBench
Output level600 Ω, before 1 % THD, ±16 V≥ +18 dBu+19.6 dBuPending
Output level600 Ω, before 1 % THD, ±24 V≥ +23 dBu+23.5 dBuPending
THD1 kHz, +18 dBu into 600 Ω, ±16 V≤ 0.05 %0.023 %Pending
THD1 kHz, +18 dBu into 600 Ω, ±24 V≤ 0.05 %0.009 %Pending
Input noise150 Ω source≤ 4 nV/√Hz3.4 nV/√HzPending
Supply currentPer rail, ±16 V / ±24 V—8.1 / 10.8 mAPending
Clip recoveryVintage / Fixed— / ≤ 60 µs≈ 260 / ≈ 50 µsPending
Output offsetUnity gain≤ 10 mV+1.4 mVPending
Supply rangeDual rails±12 V to ±24 V
Board2-layer FR-4, parts both sides28.6 × 28.6 × 1.6 mm

Short-circuit protection covers brief faults to ground. A sustained short at ±24 V is not covered. Vintage HF is for circuits with 20 dB of gain or more.

Fit

Drops into a 2520 socket.

  • PinsIN+, IN−, OUT, V−, V+ on the 2520 pattern shown, from the centre of the board.
  • HostsDesigned for ±16 V hosts like the Iron Eight and ±24 V API-style hosts. We'll publish a tested-in list as we try it in real gear.
  • PartsSurface-mount on both sides, with the tallest parts on top. Nothing to trim, nothing to socket.
  • TestedEvery module is powered up and measured before it ships.
First batch

A small run, built by hand.

The Rev A prototypes are being built and measured now. Leave your email and we'll tell you when the first batch is ready, with bench measurements, sound clips and the price.