Skyline Audio
SA-101 Rev A · first boards ordered, not yet measured

The 101,on split rails.

A discrete op amp in the style of the Spectra Sonics 101 amplifier card, rebuilt as a two-input op amp for the 2520 footprint. It keeps the all-NPN output stage, runs on ±12 to ±24 V, and one solder jumper sets how much second harmonic it adds.

Top side · drawn from the Rev A board file
Footprint252028.6 × 28.6 mm, five pins
Supply±12–24 VNo ground pin needed
Flavours3Off, light and 101 mode, on one jumper
Input noise1.75 nV/√HzSimulated, 20 Hz to 20 kHz
The original

A single-supply card, turned into an op amp.

The 101's output stage is the part worth keeping. The way it was powered and fed is the part that keeps it out of a 2520 socket.

The Spectra Sonics 101 was an amplifier card that ran from a single +24 V supply, with the signal fed into the emitter of its input transistor. The 110A was the same idea on ±24 V.

Its output stage is unusual. Where most amplifiers use a complementary pair, the 101 stacks two NPN transistors: a follower on top and a common-emitter stage below. The SA-101 keeps that stage, along with the PNP pair and three-diode reference that drive it.

The front end is new. A matched pair adds a follower on the + input, so the module behaves as an ordinary two-input op amp on split rails. One resistor had to change on the way: at the 101's 10.7 kΩ this form latched up, and at 1 kΩ it follows its input to within 2.5 V of the rails in simulation.

Original 101
Supply
Single +24 V
Input
Signal into the input transistor's emitter
Output
Two NPN transistors, stacked
Upper transistor current
Extra standing current, always
SA-101
Supply
±12 to ±24 V
Input
Two inputs on a matched pair
Output
The same two-NPN stage
Upper transistor current
Your choice: off, light or 101 mode
Signal path

Three stages, and no complementary pair.

No IC anywhere. What we added sits around the original stages: a current-sink tail, input clamp diodes, a sink current limit and rail filtering. The circuit has no ground connection, so a single 100 V capacitor sits across the filtered rails.

Stage 1 · input

Matched NPN pair

One half is the 101's input transistor. The other is a follower that buffers the + input. A current sink feeds both, so the bias holds from ±12 to ±24 V.

BCM846BS matched pair
BC846B tail sink
Stage 2 · gain

PNP pair, three-diode reference

Unchanged from the 101 and 110A. One half drives the upper output transistor and the other drives the lower. Low-leakage diodes stand in for the original 1N461A.

BC856BDW1 pair
BAS116 reference string
Stage 3 · output

Two NPNs, stacked

A follower on top and a common-emitter stage below, idling at 5 mA. A limiter caps the sink current, so the stage survives a brief short.

BCP56-16 × 2
BC846B sink limiter
Flavour

One jumper sets the second harmonic.

A three-pad solder jumper on the top side connects a resistor from the output to the negative rail. That adds standing current in the upper output transistor, the way the 101 ran, and the second harmonic rises with it.

Flavour

JP1

  • Jumper
  • Resistor
  • Supply current
  • THD
Simulated at 1 kHz, +4 dBu into 600 Ω, ±24 V. Levels are relative to the fundamental. Bench measurements will replace this chart.
Specifications

Simulated so far. Bench numbers to come.

Nothing below has been measured yet. The figures come from simulation with the transistor makers' own models, and bench measurements from the Rev A boards replace them as they come in.

ParameterConditionSimulatedBench
Input noise20 Hz to 20 kHz1.75 nV/√HzPending
THD, flavour off1 kHz, +4 dBu into 600 Ω, 40 dB gain, ±24 V0.004 %Pending
THD, 101 modeSame0.05 %Pending
Slew rateUnity gain, 600 Ω ∥ 100 pF90–137 V/µsPending
Bandwidth, −3 dB40 dB gain, 10 kΩ load, flavour off79 kHzPending
Phase marginUnity gain, ±12 to ±24 V≥ 84°Pending
Output offsetUnity gain, ±15 V, no load+0.74 mVPending
Supply currentPer rail at ±16 V: off / light / 101 mode8.5 / 10.1 / 10.8 mAPending
Short-circuit currentSink / source≈ 38 / ≈ 20 mAPending
Supply rangeDual rails±12 V to ±24 V
Board2-layer FR-4, parts both sides28.6 × 28.6 × 1.6 mm

Simulated with typical models at 25 °C. Short-circuit protection covers brief faults. A sustained short at ±24 V is not covered. In 101 mode the module clips earlier into 600 Ω loads.

Fit

Five pins on the 2520 pattern.

  • PinsIN+, IN−, OUT, V−, V+ at the offsets shown. The 2520 ground position is left empty, because the circuit doesn't use it.
  • SocketsGold Mill-Max pins, 1 mm in diameter, for Mill-Max 0322 receptacles.
  • HostsThe pin positions come from the socket in our Iron Eight, which runs ±16 V. Any 2520 host from ±12 to ±24 V suits it.
  • PartsSurface-mount on both sides, with the output transistors on top. Nothing to trim.
First batch

Rev A, on the bench next.

The first SA-101 boards are ordered. Leave your email and we'll send bench measurements, sound clips and the price when the first batch is ready.